FFE turn OFF while breaking

Ford Focus Electric Forum

Help Support Ford Focus Electric Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

disar

New member
Joined
Jul 4, 2022
Messages
2
Hi!
I have problem with my FFE 2014. When I operate accelerator pedal everything is ok, but when I stop operating car goes into service mode and turn off. I need to restart it by pressing start button.
Errors which I read from Forscan:
P0AFB Code - Battery System Voltage High
P0C07 Code - Drive Motor 'A' Phase U-V-W Circuit High
P0C05 Code - Drive Motor 'A' Phase U-V-W Circuit/Open

Sometimes I had errors with stucking "plus"contactor

I replaced TCM for used one, but it didnt solve my problem. After few test rides I have new problem - car doesnt start and I have error:
P0AF8 Code - Hybrid Battery System Voltage (too low)

Do you have any ideas what should I check now?

Where is + and - contactors? Both are at upper battery pack?
 
Wow, I have never seen those codes before:
So I guess you know that P0c07 and P0c05 deal with the TCM. Yet you replaced that. Did you replace the entire drive unit or just the box on top of the inverter?
I would check the continunity of the separate phases of the motor between the inverter, to make sure that nothing is open. Likewise, check if there are any fuses in the TCM or inverter that have blown.
The P0AFB and P0AF8 are supposedly also in the TCM. The P0AFB is a greater than 390V situation (don't know how that would happen) unless from regen braking going nuts, and the P0AF8 is a less than 190V situation. If the battery was dead.
Since these are also TCM codes, I am thinking that something is wrong with the TCM you just installed, or perhaps what the TCM connects to.
Yes, the contactors are in the upper battery. There might be two in the lower battery as well. Cannot remember.
The service manual says to replace the entire drive unit, so it can't help you with the inverter/TCM replacement.

Watch this video for visualization:
https://www.youtube.com/watch?v=ML6ucMDWS2c
 
I just replaced inverter box on top of the motor (took motor out of the car). Errors are the same with both inverters, so I think that inverter is not a problem. I checked motor phases (with standard multimeter 'resistance' ) and I didn't found any problem. Isolation has infinity resistance.

The biggest problem with TCM is that it's one of PATS system. It's very difficult to code used one.

P0AFB is active while regen braking. I check voltage at TCM while braking and it goes sometimes above 400V for less than 1s. At the same time I checked voltage in BCM and there is no problem (~360V). When I drive without braking everything is OK :shock:

I checked voltage at upper battery (before contactors) and I have ~160V. So maby P0AF8 is active becouse one of lower contactor is bad?

I think my next step will be motor replace :roll:
 
The error codes you are getting are also relevant to a contactor failure. Although you didn't show a contactor error code, you did say that you got positive contactor failures. The positive contactor is in the upper battery behind the rear seat. There are 4 contactors there on the driver side of the battery pack. When you remove the battery cover and then the subsequent contactor cover, the positive contactor is a larger contactor closest to the rear seat. The BECM will check various voltages when it expects the contactors to be closed. The the voltage doesn't match, you get an error. If you decide to service your battery, the bad contactor will likely be burnt on top or discolored with a high concentration of discoloration closest to the terminals. If you are interested, I can send some pictures. Or join the FFE facebook page and look for my contributions under David Brewer. I've serviced my upper and lower contactors. The the lower contactors, I showed what I did in a PDF in the "files" section for that group. This was just last December. The upper contactor was changed in summer of 2022.

I'd be willing to bet it is a contactor issue. And the upper contactors are not so hard to replace. But, that assumes you know what you are doing and can be safe doing so.
 
Here are some photos of my contactor replacement of the upper and some from the lower battery. You can see the difference between good and bad. A good contactor will be of uniform color. A bad contactor will have anywhere from a little to a lot of discoloration. The discoloration means that the contactor is getting warm...meaning there is resistance in the contactor. Shown also in the pictures is a contactor cut in half. This is at the point of failure...meaning that just before this, it seemed to be working fine. In the pic of the two contactors installed side by side, one is bad and one is going bad...I replaced both.
 

Attachments

  • PXL_20220910_225333847.jpg
    PXL_20220910_225333847.jpg
    1.9 MB · Views: 0
  • PXL_20220924_155134969.MP.jpg
    PXL_20220924_155134969.MP.jpg
    4 MB · Views: 0
  • PXL_20220924_155141837.jpg
    PXL_20220924_155141837.jpg
    1.8 MB · Views: 0
  • PXL_20220924_161115484.jpg
    PXL_20220924_161115484.jpg
    1.9 MB · Views: 0
  • PXL_20231223_203551016.jpg
    PXL_20231223_203551016.jpg
    2 MB · Views: 0
  • PXL_20231223_211225464.jpg
    PXL_20231223_211225464.jpg
    1.6 MB · Views: 0
  • PXL_20240127_184244158.jpg
    PXL_20240127_184244158.jpg
    1.6 MB · Views: 0
  • PXL_20240127_184259861.jpg
    PXL_20240127_184259861.jpg
    1.7 MB · Views: 0
Back
Top